801-974-0511

Cat® C2.8 Diesel Engine

  • Home »
  • New Powers » Cat® C2.8 Diesel Engine
    Order Parts Request Service

    Cat® C2.8 Diesel Engine

    Email/Share
    Engine Configuration
    In-Line 4, 4-Stroke-Cycle Diesel
    Cooling System Capacity
    4 L (1.06 qt)
    DOC Length
    TBA
    DOC Weight
    TBA

    General

    Engine Configuration
    In-Line 4, 4-Stroke-Cycle Diesel
    Cooling System Capacity
    4 L (1.06 qt)
    Bore
    3.5in
    Stroke
    4.3in
    Displacement
    171in³
    Aspiration
    Turbocharged (T) and Turbocharged-Aftercooled (TA)
    Compression Ratio
    17.0:1
    Combustion System
    Direct Injection
    Rotation from Flywheel End
    Counterclockwise
    Engine Configuration
    In-Line 4
    Bore
    90 mm (3.5 in)
    Stroke
    110 mm (4.3 in)
    Displacement
    2.8 L (171 in³)
    Cooling System - Capacity
    4 L (1.06 qt)

    Aftertreatment Dimensions (Approximate. Final dimensions dependent on selected options)

    DOC Length
    TBA
    DOC Weight
    TBA
    DOC Diameter
    TBA

    Aftertreatment Dimensions - Approximate

    DOC Diameter
    TBA
    DOC Length
    TBA
    DOC Weight
    TBA

    Engine Dimensions - Approximate

    Height
    786 mm (30.9 in)
    Length
    633 mm (24.9 in)
    Width
    543 mm (22.4 in)
    Dry Weight - Basic Operating Engine Without Optional Attachments
    340 kg (750 lb)
    Weight - Net Dry - Basic Operating Engine Without Optional Attachments
    750lb
    Width
    22.4in
    Height
    30.9in
    Length
    24.9in

    Power Rating

    Minimum Power
    67HP
    Maximum Power
    74HP
    Rated Speed
    2200 - 2400 rpm
    Maximum Torque
    280lb-ft @ 1360 rpm

    Emission Standards

    Emissions
    U.S. EPA & CARB Tier 4 Final, EU Stage V

    Engine Dimensions (Approximate. Final dimensions dependent on selected options)

    Length
    635 mm (25.0 in)
    Width
    561 mm (22.1 in)
    Height
    766 mm (30.2 in)

    Standard Equipment:

    • Air Inlet System
      • Induction manifolds
      • Exhaust manifolds
      • Engine-mounted aftertreatment
    • Control System
      • Starter motor (12V)
      • Alternator (12V)
      • Electronic Control Unit (chassis mounted)
      • Engine control sensors and robust wiring harness
      • Data interface via CANbus J1939
    • Flywheels And Flywheel Housing
      • Flywheel housings – SAE 3 or SAE 4
      • Choice of flywheel to match industry common hydraulic pumps and transmissions
      • Side PTO with SAE A or SAE B interface
    • Fuel System
      • Fuel filter – preconnected but chassis mounted
      • With water sensor
    • Lube System
      • Lubricating oil filters
      • High incline oil pan – 35° continuous in all directions
    • General
      • Cold start capability to -20° C (-4° F) with standard equipment
      • Paint: Caterpillar yellow, with optional colors available at request
    • U.s. Epa Tier 4 Final, Proposed Eu Stage V Aftertreatment/ Clean Emissions Control Equipment
      • Diesel Oxidation Catalyst (DOC) (Tier 4 Final and Stage V)
      • Diesel Particulate Filter (DPF) (Stage V)

    Optional Equipment: