Standard Equipment:

• Air Inlet System

  • Single turbocharger, mid-mounted, inlet 152.4 mm (6 in), hoseconnection
  • Dual turbocharger, front and rear inlet 127.0 mm (5 in.), hoseconnection

• Control System

  • Electronic governing, PTO speed control
  • Programmable ratings
  • Cold mode start strategy
  • Automatic altitude compensation
  • Power compensation for fuel temperature
  • Programmable low and high idle and TEL
  • Electronic diagnostics and fault logging
  • Engine monitoring and protection system (speed, temperature,pressure)
  • J1939 Broadcast (diagnostic, engine status, and control)

• Cooling System

  • Thermostats and housing — outlet vertical
  • Jacket water pump — gear-driven, centrifuga
  • RH front water pump inlet
  • All plugs/fittings are STOR for lines gp water

• Exhaust System

  • Exhaust manifold — dry
  • Single turbo — front-facing turbo exhaust, full marmonconnection, maximum load 10 kg for direct connection to turbo
  • Dual turbo — exhaust elbow, dry 203 mm (8 in)

• Flywheels And Flywheel Housings

  • See Mandatory Options

• Fuel System

  • Electronic unit injector
  • Fuel filter, secondary, mid-mount (LH 2 micron high performance)
  • Fuel transfer pump, LH front
  • Fuel priming pump, LH mid-mount
  • Fuel sample valve, mounted on fuel filter base.

• Lube System

  • Crankcase breather — rear valve cover
  • Oil cooler — RH (dual)
  • Oil filter — RH, LH
  • Oil pan — front sump
  • Oil dipstick — LH front
  • Oil pump

• Mounting System

  • Front support (shipping only)

• Power Take-offs

  • Crankshaft pulley, 203.2 mm (8 in), 3 grooves 292.1 mm(11.5 in) 1 groove, all 15.9 mm (.63 in) width
  • Hydraulic pump drive, SAE A, 11-tooth

• General

  • Vibration damper
  • Paint — Cat yellow
  • Lifting eyes
  • Automatic variable timing, electronic
  • Electronic installation kit 70-pin connector (connectors, pins,sockets)

• Mandatory Options

  • Throttle position sensor
  • Single turbo only — exhaust system (front or rear)
  • Flywheel housing or rear PTO
  • Primary filter/water separator

Optional Equipment:

• Air Compressor

  • Air compressor governor
  • Expansion chambers

• Air Inlet System

  • Air cleaners
  • Air lines

• Charging System

  • Charging alternators
  • Alternator mountings
  • Alternator wiring
  • Circuit breakers and mountings
  • Alternator belt guard

• Cooling System

  • Radiator
  • Fan drive with radiator packages
  • Fan height instructions
  • Vee belts
  • Aftercooler lines with Caterpillar installed radiator
  • Single turbo configuration rear-facing exhaust
  • Single turbo configuration rear-facing exhaust
  • Aftercoooler lines
  • Suction fan adapters
  • Blower fan adapter
  • Blower fan
  • Suction fan
  • Fan belt
  • Coolant level sensor
  • Dry charge coolant conditioners

• Exhaust System

  • Turbo exhaust connection
  • Flexible fittings
  • Elbows, flange, clamp, pipes
  • Exhaust adapters
  • Manifold
  • Mufflers

• Fuel Systems

  • Flexible fuel lines
  • Fuel filter location
  • Fuel cooler
  • Water separator

• Instrumentation

  • Gauges and instrument panels

• Lube System

  • Oil pans
  • Drain and cover
  • Oil level gauge
  • Remote oil filters
  • Oil filters
  • Lubricating oils

• Mounting System

  • Structural steel base
  • Front and rear engine support

• Power Take-offs

  • Rear enclosed clutches
  • Hydraulic pump drives
  • Hydraulics gear pumps
  • Clutch supports
  • Crankshaft pulleys

• Protection System

  • Air shutoff

• Starting System

  • Air starting motors
  • Air pressure regulator
  • Air silencer
  • Start switch
  • Electric starting motors — 12V, 24V
  • Battery sets – 24V
  • Battery cable and rack
  • Starting aids

• Transmission Arrangement

  • Transmission water lines