C27 ACERT Land Mechanical Drilling Engine

C27 ACERT Land Mechanical Drilling Engine

Minimum Rating
800.0 bhp
Maximum Rating
1150.0 bhp
Emissions
U.S. EPA Non-road Tier 2
Rated Speed
2100.0 RPM

Engine Specifications

Minimum Rating
800.0bhp
Maximum Rating
1150.0bhp
Emissions
U.S. EPA Non-road Tier 2
Rated Speed
2100.0RPM
Bore
5.4in
Stroke
6.0in
Displacement
1658.0in3
Aspiration
Turbocharged-Aftercooled
Engine Weight, net dry
6382.0lb
Oil Change Interval
250
Rotation (from flywheel end)
Counterclockwise
Flywheel and Flywheel Housing
SAE No. 0 or SAE No. 1
Flywheel Teeth
136 (SAE 0), 113 (SAE 1)
Governor and Protection
ADEM A3
Minimum Rating
800BHP
Maximum Rating
1150BHP
Emissions
U.S. EPA Non-road Tier 2
Rated Speed
2100r/min
Bore
5.4in
Stroke
6in
Displacement
1658in³
Aspiration
Turbocharged-Aftercooled
Engine Weight - Net Dry
6382lb
Oil Change Interval
250
Rotation from Flywheel End
Counterclockwise
Flywheel and Flywheel Housing
SAE No. 0 or SAE No. 1
Flywheel Teeth
136 (SAE 0), 113 (SAE 1)

Dimensions

Length
75.5in
Width
57.6in
Height
52.0in
Length
75.5in
Width
57.6in
Height
52in

Capacity for Liquids

Minimum Cooling System - Engine Only
14.5gal (US)

Standard Equipment:

  • Air Inlet System
    • Dual turbochargers side or rear mounted — inlet 152.4 mm (6 in.) hose connection
  • Control System
    • Electronic governing, PTO speed control
    • Programmable ratings
    • Cold mode start strategy
    • Automatic altitude compensation
    • Power compensation for fuel temperature
    • Programmable low and high idle and TEL
    • Electronic diagnostics and fault logging
    • Engine monitoring and protection system (speed, temperature, pressure)
    • J1939 Broadcast (diagnostic, engine status, and control)
  • Cooling System
    • Thermostats and housing — outlet LH vertical orientation
    • Jacket water pump — gear-driven, centrifugal RH
  • Exhaust System
    • Exhaust manifold — dry, heat shields
    • Dual turbo — rear turbo exhaust, full marmon connection 127 mm (5 in.), maximum load 10 kg for direct
    • Water-cooled center sections
  • Flywheels And Flywheel Housings
    • SAE No. 0 or SAE No. 1
    • SAE standard rotation
  • Fuel System
    • MEUI system
    • Fuel filter, RH ( 2 micron high performance)
    • Fuel transfer pump
    • Fuel priming pump (optional electric priming pump)
  • Lube System
    • Crankcase breather — rear mounted
    • Oil cooler — RH
    • Side turbo — oil filler in RH front gear case
    • Rear turbo — oil filler in RH valve cover
    • Oil level gauge — RH
    • Oil filter — RH
    • Oil pan rear sump
  • Mounting System
    • Front support — narrow
  • Power Take-offs
    • Crankshaft pulley — 203.2 mm (8 in), 5 grooves 15.9 mm (.63 in) wide; 292.1 mm (11.5 in.) 1 groove 15.9 mm (.63 in.) wide
  • General
    • Vibration damper
    • Paint — Cat yellow
    • Lifting eyes
    • Automatic variable timing, electronic
    • Electronic installation kit 70-pin connector (connectors, pins, sockets)

Optional Equipment:

  • Air Inlet System
    • Air lines
    • Air cleaners
    • Precleaners
  • Charging System
    • Battery chargers
    • Charging alternators
    • Alternator mountings
  • Circuit Breakers
    • Circuit breaker mounting
  • Cooling System
    • Blower fans
    • Suction fans
    • Radiators
  • Exhaust System
    • Muffler
  • Fuel Systems
    • Electric fuel priming pump
  • Instrumentation
    • Gauges and instrument panels
  • Lube System
    • Lubricating oil
    • Oil pan
    • Oil filter
  • Mounting System
    • Engine supports
  • Power Take-offs
    • Hydraulic pump drives
    • Pulley
    • Auxiliary drive
  • Starting System
    • Electric starting motor
    • Battery sets - 24V
    • Battery cable
    • Battery rack
    • Starting aids
  • Packaging
    • Overseas preservation
    • Storage preservation
    • Export packaging