Standard Equipment:

• Air Inlet System

  • Turbocharger, separate circuit (SCAC) or remote (REMAC)aftercooler
  • Single, right-side, center-mounted turbo with water-cooledturbine housing
  • Air inlet 101.6 mm (4 in) connection type

• Control System

  • Electronic governing, PTO speed control
  • Programmable ratings
  • Cold mode start strategy
  • Automatic altitude compensation
  • Fuel cooled ECU
  • Power compensation for fuel temperature
  • Programmable low and high idle
  • Electronic diagnostics and fault logging
  • Programmable monitoring system (engine speed, temperature,pressure)
  • J1939 broadcast (diagnostic and engine status)
  • Certified electrical control system (hazardous environment only)
  • Derated engine: automatic ambient temperature compensation

• Cooling System

  • Thermostats and housing, RH forward-facing outlet — 51 mm(2.01 in) connection
  • Jacket water pump — belt-driven, centrifugal
  • Water pump — inlet RH facing downward 63 mm (2.48 in)

• Exhaust System

  • Exhaust manifold — water-cooled
  • Single, right-side, center-mounted turbo with water-cooledturbine housing
  • Rear facing turbo exhaust 81.8 mm (3.22 in) connection, nonV-band clamp

• Flywheels And Flywheel Housing

  • Mandatory selection of:SAE No. 1 or SAE No. 2 flywheel and housing, SAE standard rotation

• Fuel System

  • HEUI fuel system
  • Fuel filter — secondary, LH (2-micron high performance)
  • Fuel transfer pump — left front
  • Fuel priming pump — left front

• Lube System

  • Crankcase breather — LH
  • Crankcase fumes disposal — with integrated service indicator, LH
  • Oil cooler — RH
  • Oil filter — RH
  • Oil pan — front sump
  • Oil filler — top mounted
  • Oil level gauge — LH side
  • Oil pump — gear-driven
  • Oil valve sampling
  • Preservation of turbocharger, flywheel, and crankcase

• Power Take-offs

  • Crankshaft drive pulley — 2 grooves, 190 mm (7.5 in) diameter,22.3 mm (7/8 in) wide

• General

  • Vibration damper
  • Lifting eyes
  • Automatic variable timing — electronic
  • Literature

• Mandatory Options

  • Flywheel housing and flywheel
  • Throttle position sensor and/or throttle control
  • (Non-hazardous environment only)
  • Primary filter/water separator
  • Turbo orientation

Optional Equipment:

• Air Compressors

  • Air compressors
  • Air compressor governor

• Air Inlet System

  • Air cleaner
  • Precleaner
  • Air inlet elbow
  • Air shutoffs

• Charging Systems

  • Charging alternators
  • Alternator mounting
  • Alternator belt tensioner
  • Alternator pulleys
  • Alternator guards

• Cooling System

  • Radiators
  • Fan drive and pulley — f/u/w radiator packages
  • Fans f/u/w radiator packages
  • Coolant level sensor
  • Fan drive mountings
  • Fan adapters
  • Fan adapter for blower fans
  • Fan pulleys
  • Fan height instructions
  • Vee belts for customer-supplied radiators
  • Suction fans and blower fans
  • Water inlet elbows
  • Dry charge coolant conditioners

• Emissions Certifications

  • IMO certification

• Exhaust System

  • Flexible fitting
  • Turbocharger exhaust outlet adapters
  • Elbows, flange, pipes, clamp
  • Rain caps
  • Manifolds
  • Mufflers

• Flywheels And Flywheel Housing

  • Crankshaft seal

• Fuel System

  • Flexible fuel lines
  • Water separator and fuel filters
  • Fuel cooler

• Instrumentation

  • Gauges and instrument panels
  • Interconnect harness
  • Voltmeters
  • Gauge mounting
  • Ammeter

• Lube System

  • Oil pans
  • Drain and cover
  • Oil level gauges
  • Remote oil filter
  • Oil fillers
  • Lubricating oil
  • Fumes disposal

• Mounting System

  • Structural steel base
  • Engine support — front and rear

• Power Take-offs

  • Enclosed clutch
  • Clutch supports
  • Flywheel stub shaft
  • Hydraulic pump drives
  • Hydraulic gear pumps

• Starting System

  • Starting aids
  • Electric starting motors — 12V and 24V
  • Battery sets — 12V and 24V (dry)
  • Battery cable

• General

  • Tool set