The Cat® 920 Small Wheel Loader features an optimized Z-bar linkage that combines the digging efficiency of a traditional Z-bar loader with tool carrier capabilities for great performance and versatility. With parallel lift and high tilt forces throughout the working range you can safely and confidently handle loads with precise control. A new engine layout greatly improves rear visibility and service access.
Maximum Gross Power 121 hp
Operating Weight 21742 lb
Bucket Capacities 1.3-3.5 m3 (1.7-4.6 yd3)
Rated Net Power - Rated Engine Speed 2200 r/min
Bore 3.85in
Displacement 220in³
Emissions Engine meets Tier 4 Final/Stage V emission standards.
Engine Model Cat C3.6
Maximum Gross Power 121hp
Maximum Gross Power - ISO 14396 121hp
Maximum Gross Power - ISO 14396 (metric) 122hp
Maximum Gross Power - Rated Engine Speed 2200r/min
Maximum Gross Torque - ISO 14396 369ft·lbf
Maximum Gross Torque - SAE J1995 372ft·lbf
Maximum Net Torque - ISO 9249 363ft·lbf
Maximum Net Torque - SAE J1349 366ft·lbf
Note Net power advertised is the power available at the flywheel plus front drive implement pump when the engine is equipped with fan, air cleaner, muffler and alternator.
Rated Net Power - ISO 9249 118hp
Rated Net Power - Rated Engine Speed 2200r/min
Rated Net Power - SAE J1349 120hp
Stroke 4.72in
Operating Weight 21742lb
Bucket Capacities 1.3-3.5 m3 (1.7-4.6 yd3)
Bucket Capacities - General Purpose 1.3-1.9 m³ (1.7-2.5 yd³)
Bucket Capacities - Light Material 2.5-3.5 m³ (3.3-4.6 yd³)
Recyclability 95%
Axles - Front 4.5gal (US)
Axles - Rear 4.5gal (US)
Cooling System 5.7gal (US)
Diesel Exhaust Fluid (DEF) Tank 4.8gal (US)
Engine Crankcase 2.6gal (US)
Fuel Tank 43.6gal (US)
Hydraulic System - Including Tank 25.9gal (US)
Hydraulic Tank 14.5gal (US)
Note DEF used in Cat Selective Catalyst Reduction (SCR) systems must meet the requirements outlined in the International Organization for Standardization (ISO) standard 22241-1.
Transmission 0.8gal (US)
FOPS ISO 3449:2005
Note (1) Cab and Rollover Protective Structures (ROPS) are standard in North America and Europe.
Note (2) The declared dynamic operator sound pressure levels per ISO 6396:2008*, when the cab is properly installed and maintained, is 77 dB(A).
Note (3) The labelled sound power level for the CE marked configurations when measured according to the test procedure and conditions specified in 2000/14/EC (as amended by 2005/88/EC) is 103 dB(A).
Note (4) *The measurements were conducted with the cab doors and windows closed.
ROPS ISO 3471:2008
Forward and Reverse - Speed Range 1* 6.3mile/h
Forward and Reverse - Speed Range 2* 12.5mile/h
Forward and Reverse - Speed Range 3 25mile/h
Note *Creeper Control allows speed control from a stand still up to 10 km/h (6.3 mph). The Creeper Control will only work in Range 1.
Front Fixed; Locking differential (standard)
Rear Oscillating ±11 degrees; Locking differential (standard)
Note (1) Other tire choices are available. Contact your Cat dealer for details.
Note (2) In certain applications, the loader’s productive capabilities may exceed the tire’s tonnes-km/h (ton-mph) capabilities.
Note (3) Caterpillar recommends that you consult a tire supplier to evaluate all conditions before selecting a tire model.
Other Choices Include 17.5 R25 L3 XHA2; 20.5 R25 L3 XHA3; 17.5-25 L2/L3 SGL; 20.5-25 L2/L3 SGL; 17.5-25 L3 HRL D/L-3A; 17.5 R25 L2 Snow; 20.5 R25 L2 Snow; 17.5 R25 Solid
Standard Size 17.5 R25 L2 XTLA
Maximum Flow - Steering Pump 21.7gpm
Maximum Working Pressure - Steering Pump 3190psi
Number of Steering Wheel Turns - Full Left to Full Right or Full Right to Full Left 3.4turns
Steering Articulation Angle - Each Direction 40°
Steering Cycle Times - Full Left to Full Right - At 2,350 rpm: 90 rpm Steering Wheel Speed 2.3s
Hydraulic Cycle Time - Dump, at Maximum Reach 1.8s
Hydraulic Cycle Time - Float Down, Maximum Lift to Ground Level 2.7s
Hydraulic Cycle Time - Rackback 2.2s
Hydraulic Cycle Time - Raise, Ground Level to Maximum Lift 4.8s
Hydraulic Cycle Time - Total Cycle Time 11.5s
Maximum Flow - Implement Pump 43.6gpm
Maximum Flow - Implement Pump - 3rd Function, Maximum Flow, High 40gpm
Maximum Flow - Implement Pump - 3rd Function, Maximum Flow, Standard 25gpm
Maximum Flow - Implement Pump - 4rd Function, Maximum Flow 25gpm
Maximum Working Pressure - Implement Pump 4061psi
Note All cycle times listed are with cylinder snubbing turned off.
Relief Pressure - Tilt Cylinder 4641psi
Relief Pressure - Tilt Cylinder - 4th Function Relief Pressure 4641psi
