Cat C32 ACERT hazardous location engines are the ideal solution for specialized and demanding operations in the oilfield. Engines are hazardous-location certified from the factory to minimize installation design, time, and cost. Decades of field operation and intense research and development allow Cat C32 ACERT hazardous location engines to deliver excellent performance with low operating costs and emissions. Hazardous location engines are certified to operate in potentially explosive environments. Applications powered by C32 ACERT engines include well stimulation pumping, pump skids, nitrogen units, acidizing units, blenders, and hydraulic power units. Cat engines are backed by the worldwide network of Cat dealers ready to support your operation with technical support, service, parts, and warranty. C32 ACERT hazardous location engines, with ratings 597-828 bkW (800-1110 bhp) @ 2100 rpm meet IMO Tier II, U.S. EPA Marine Tier 2, and U.S. EPA Non-road Tier 2 equivalent emission standards. They are available using U.S. EPA and EU Flexibility, and for other regulated and non-regulated areas.
Maximum Rating 1110 BHP
Emissions U.S. Non-Road Tier 2 CARB, IMO Tier II, EPA Marine Tier 2
Displacement 1960 in³
Minimum Rating 800 BHP
Aspiration Turbocharged-Aftercooled
Bore 5.7in
Displacement 1960in³
Flywheel Teeth 136
Flywheel and Flywheel Housing SAE No. 0 or SAE No. 1
Maximum Rating 1110BHP
Minimum Rating 800BHP
Stroke 6.4in
Emissions U.S. Non-Road Tier 2 CARB, IMO Tier II, EPA Marine Tier 2
Height 54.66in
Length 76.18in
Weight 6950lb
Width 56.34in
Dual side-mounted turbochargers — inlet 152.4 mm (6 in) hose connection
Programmable ratings
Cold mode start strategy
Automatic altitude compensation
Power compensation for fuel temperature
Programmable low and high idle
Electronic diagnostics and fault logging
Engine monitoring and protection system (speed, temperature, pressure)
J1939 Broadcast (diagnostic, engine status and control)
Electronic governing, PTO speed control
Certified electrical control system
Customer interface harness available as optional attachment
Thermostats and housing — outlet LH vertical orientation
Jacket water pump — gear-driven, centrifugal, RH
Exhaust manifold, water-cooled
Dual turbo, rear turbo exhaust, full marmon connection 127 mm (5 in), maximum load 10 kg for direct connection to turbo
Water-cooled center sections
Mandatory selection of: SAE No. 0 or SAE No. 1 flywheel and housing SAE standard rotation
MEUI fuel system
Fuel filter — RH (2 micron high performance)
Fuel transfer pump
Fuel priming pump
Crankcase breather — rear-mounted
Oil cooler — RH
Oil filler in RH front gear case
Oil filter — RH
Oil level gauge — RH
Oil pan rear sump
Narrow front support
Crankshaft pulley — 203.2 mm (8 in) 5 grooves 15.9 (.63 in) wide; 292.1 mm (11.5 in) 1 groove 15.9 (.63 in) wide
Paint — Cat yellow
Vibration damper with single pulley
Lifting eyes
Automatic variable timing — electronic
Electronic installation kit 70-pin connector (connectors, pins, socket)
HP must be specified when ordering
All engines shipped at 2100 rpm
Flywheel housing
These engines meet the current IMO emission standards as defined by Regulation 13 of Annex VI to the International Convention for the Prevention of Pollution from Ships, 1973, as modified by the Protocol of 1978, further amended by the Protocol of 1997. A statement of compliance issued by the United States government's EPA (Environmental Protection Agency) is included in the technical file that is shipped with the engine as proof of our engine's ability to meet IMO emissions requirements. If this technical file is insufficient to meet the customer's requirements, then a GL or CCS IMO emissions certification may be ordered.
Air cleaner
Air inlet adapters
Turbocharger outlet adapters
Air lines
Battery chargers
Charging alternators
Alternator mounting
Circuit breakers and mountings
Dry charge coolant conditioners
Thermostat housing
Coolant level sensor
Radiator
Suction fans and blower fans
Fan adapters
Fan drives
IMO certifications
Elbows
Mufflers
Electric fuel priming pump
Customer management device
Interconnect harness
Gauges and instrument panels
Oil pans
Oil service side
Oil level gauge
Oil filters
Lubricating oils
Structural steel base
Engine support — front and rear
Auxiliary drive
Damper pulley
Hydraulics gear pumps
Mechanical shutoffs
Solenoid shutoffs
Electric starting motors - 12V, 24V
Battery sets - 24V
Battery rack and cable
Starting aids
Transmission water lines
Transmission cooler
